.50 Caliber Special Contours

50sp47The chart below has a listing of special .50 caliber programs that we have made in the past. Although listed as .50 caliber contours intended for the .50 BMG cartridge these can also be used for smaller calibers using the bigger diameter steel blanks such as the .338, .375 .408 and .416 calibers.

A CAD drawing of these profiles can be viewed as a .pdf file by clicking on the orange designation in the left column. We are also adding the weight (in pounds and with a .510″ groove diameter) for the profiled blank along with the CAD drawings.

2/26/2024 Lilja .50 tapers & Contours      
         
updated        
Designation Special Profiles blank dia. barrel weight blank length
         
         
175hv31 1.750″ for 5″ then st. taper to 1.360″ at 31″ (.015″ per inch) 1.75 15.27 31
2htarg39 2.000″ for 7″ then st. taper to 1.500″ at 39″ 2 25.26 39
50spcl 1.750″ for 5″ then st. taper over 9″ to 1.500″ then 1.500″ st. cylinder to muzzle 1.75 15.89 33
         
spplus 1.700″ for 6″ then taper to 1.400″ at 8″ then st. taper to 1.250″ at 32″ finish length 1.75 12.47 33
         
PMC 1.750″ dia. for 5″ then straight cylinder dia. of 1.625″ for 28.5″ 1.75 16.46 34
         
50test 1.999″ dia. for 8″ then 1.620″ dia. straight  w/corner radius 2 19.30 33
50sp1 1.950″ dia. for 8.5″ then st. taper to 1.664″ at 36″ (.010″/”) 2 24.48 36
50sp2 1.960″ for 7.5″ then st. taper to 1.214″ at 38″ (.024″/inch) 2 21.06 38
50sp3 2.000″ for 7″ then st. taper to 1.625″ at 34″ 2 23.45 34
50sp4 No longer make this profile      
50sp5 1.960″ for 9″ then st. taper to 1.500″ at 34″ (1.482″ at 35″) for 32″ finish length barrel 2 22.32 35
         
50sp6 1.750″ for 5″ then st. taper to 1.600″ at 31″ 1.75 17.39 31
50sp7 1.750″ for 12″ then 1.450″ dia st. cylinder 1.75 14.88 31
50sp8 2.000″ for 8″ then st. taper to 1.863″ at 41″ 2 31.32 41
50sp9 1.750″ for 7″ then 1.145″ dia. Cyl. W/radius in corner 1.75 9.74 31
50sp10 1.625″ for 8″ then st. taper to 1.350″ at 40″ 1.75 17.72 41
50sp11 1.740″ for 3″ then radius down to 1.500″ over 1.5″ then st. taper to 1.280″ at 31″ (Amack) 1.75 12.18 31
         
50sp12 1.900″ dia. For 6″ then st. taper to 1.700″ at 38″ (1.694″ at 39″) makes 36″ long finish length barrel 2″ 25.62 39
         
50sp13 2.060″ for 8″ (plus 1.75″ of 1.75″ dia. For drilling) then st. taper to 1.850″ at a finish length of 37″ (1.841″ at 40″) 2.06 31.52 40
         
50sp14 2.000″ for 7″ then st. taper to 1.376″ at 33″ 2 20.45 33
50sp15 1.750″ for 9″ then st. taper to 1.500″ at 33″ 1.75 17.88 33
50sp16 2.000 for 12″ then st. taper to 1.850″ at 39″ 2 29.91 39
50sp17 1.960″ for 9″ then st. taper to 1.395″ at 36″ (1.500″ at 31″) 2 22.09 36
50sp18 1.700″ for 5″ then st. taper to 1.360″ at 30″ (1.346″ at 31″) 1.75 14.52 31
50sp19 1.750″ for 8.0″ then st. taper to 1.283″ at 35″ (1.300″) at 34″ 1.75 16.90 35
 50sp20  No longer make this contour      
50sp21 1.900″ for 10″ then st. taper to 1.487″ at 41″ 2 24.88 41
50sp22 1.750″ for 5″ then 45º taper down to 1.562″ dia. cylinder 1.75 16.27 33
50sp23 1.750″ for 5″ then 45º taper down to 1.562″ dia. cylinder 1.75 18.16 37
50sp24 1.750″ for 5.4″ then 45º taper down to 1.570″ dia. then st. taper out to 1.307″ at 37″ 1.75 15.72 37
         
50sp25 2.000″ dia. for 5.25″ then 1.250″ dia. cyl. to muzzle with radius in corner, 31″ finish length 2 12.13 33
         
50sp26 1.800″ for 10″ then st taper to 1.204″ at 41″ 2 20.07 41
50sp27 2.250″ for 6″ then 1.562″ to muzzle, 45º transition to 1.562″ 2.25 21.0 37
50sp28 1.750″ for 24″ then st. taper to 1.500″ at 38″ 1.75 21.82 38
50sp29 1.750″ for 4.10″ then radius over 4″ to 1.50″ then st taper to 1.375″ at 32″ 1.75 13.74 32
         
 50sp30  No longer make this contour      
         
50sp31 1.750″ for 7″ then taper to 1.625″ over 2″ then 1.625″ to muzzle 1.75 19.31 36
         
50sp32
1.800″ for 7″ then st. taper to 1.540″ at 35″
2 19.90 34
50sp33
1.625″ for 24″ then st. taper to 1.250″ at 37″ (turn to 1.625″ dia. straight first)
1.75 17.51 37
         
50sp34
2.000″ for 14″ then st. taper to 1.741″ at 43″ (1.750″ at42″)
2 31.74 43
 50sp35  No longer make this contour      
50sp36 2.000″ for 7″ then st. taper to 1.750″ at 38″ 2 27.59 38
50sp37 1.700 for 7″ then st. taper to 1.285″ at 35″ 1.75 16.02 35
50sp38 1.625″ for 11″ then taper to 1.305″ dia cylinder to muzzle 1.75 14.10 37
50sp39 1.950″ for 12″ then st. taper to 1.400″ at 38″ 2 23.70 38
 50sp40  1.750″ for 7.0″ then taper over 9″ to 1.5″ then straight taper to 1.239″ at 35″  1.75  14.75  35
 50sp41  No longer make this contour      
50sp42 2.000″ for 7″ then st. taper to 1.750″ at 34″ 2 24.76 34
 50sp43  1.950″ for 15.0″ then st. taper to 1.925″ at 36″  2  28.71  36
 50sp44  1.750″ for 8.0″ then st. taper to 1.375″ at 37″  1.75  18.01  37
 50sp45  1.875″ for 15.0″  st. taper to 1.425″ at 38.0″  2.0  24.43  38
 50sp46  1.750″ for 7.0″  then st. taper to 1.273″ at 38.0″  1.75  19.09  38
 50sp47  1.750″ for 7.0″ then st. taper to 1.200″ at 38.0″  1.75    38
 50sp48  1.570″ for 5.400″ then st. taper to 1.307″ at 33.0″  1.75  13.8  33
 50sp49  1.800″ for 8.0″ then st. taper to 1.200″ at 36.0″  2.0  18.49  36
 50sp50  1.750″ for 8.0″ then st. taper to 1.200″ at 36.0″  1.75  17.68  36
 50sp51  1.625″ for 8.0″ then st. taper to 1.350″ at 36.0″  1.75  17.31  36
 50sp52  2.0″ for 10.0″ then st. taper to 1.500″ at 42.0″  2.0  28.37  42
 50sp53  1.620″ for 7.0″ then st. taper to 1.467″ at 44″  1.75  22.22  44
50sp54 1.700″ for 8.0″ then radius of 98.24″ over 4.0″ to 1.5″ then st. taper to 1.250″ at 39.0″ 1.75 17.15 39
50sp55 1.600″ for 7.0″ then st. taper to 1.200″ at 34.0″  1.75 14.70 34
50sp56 1.950″ for 12.0″ then st. taper to 1.350″ at 40.0″ 2.0 24.85 40
50sp57 1.750″ for 8.0″ then st. taper to 1.250″ at 36.0″ 1.75 17.81 36
50sp58 2.000″ for 5.0″ then st. taper to 1.500″ at 36.0″ 2.0 24.46 36
50sp59 1.700″ for 7.0″ then st.  taper to 1.400″ at 33.0″ 1.75 17.32 33
50sp60 1.500″ for 6.0″ then st. taper to 1.300″ at 37.0″ 1.5 15.31 37
50sp61 1.650″ for 8.0″ then st. taper to 1.150″ at 44″ 1.75 18.07 44
50sp62 1.620″ for 8.0″ then st. taper to 1.150″ at 36.0″ 1.75 14.58 36
50sp63 1.750″ for 12.0″, then st. taper to 1.375″ over 7.0″, then st. 1.375″ to muzzle at 44″ 1.75 19.86 44
50sp64 1.700″ for 7.0″ then st. taper to 1.470″ at 30.0″  1.75 16.75 30
50sp65 2.000″ for 7.0″ then st. taper to 1.750″ at 40″ 2.0 29.61 40
50sp66 1.450″ for 10.0″ then st. taper to 1.220″ at 36.0 1.5 14.93 36
50sp67 1.750″ for 9.0″ then st. taper to 1.450″ at 35″ 1.75 18.86 35
50sp68 1.600″ for 8.0″ then st. taper to 1.100″ at 36.0″ 1.75 13.88 36
50sp69 1.850″ for 7.0″ then st. taper to 1.600″ at 34″ 2.0 21.16 34″
50sp70 1.725″ for 4.0″ then st. taper to 1.280″ at 32″ 1.75 15.21 32
         
         
lt32minus 1.700″ for 4″ then st. taper to 1.150″ at 32″ 1.75 13.18 32
EDM 1.700″ for 3.7″ then 1.355″ cylinder w/radius in corner 1.75 11.46 32
EDM2 1.700″ for 3.6″ then 1.355″ cylinder w/radius in corner 1.75 11.10 31
EDM3 1.700″ for 3.7″ then 1.355″ cylinder w/radius in corner 1.75 13.49 37
EDM4 1.700″ for 3.7″ then 1.355″ cylinder w/radius in corner 1.75 11.93 33
EDM 416 1.750″ dia. for 3.5″ then straight cylinder of 1.360″ dia. 1.75 11.61 31
         
maadi 1.500″ dia. For 18″ then 1.380″ dia for 1.500″ then st. taper to 1.242″ at 37″ (1.250″ at 36″) 1.5 13.84 37
         
         
         
         
xpa50 special profile for Proof / XPA 1.75   33
         
         
EPVAT 2.00″ for 6.5″ then 1.250″ dia cylinder w/radius 2 N/A 29
taper 8 1.740″ for 7″ then st. taper to 1.700″ at 29″ 1.75 18.11 33
taper 44 1.750″ for 10″ then st. taper to 1.500″ at 36″ 1.75 19.52 36
         
  Light Target      
50targ31 1.700″ for 6″ then st. taper to 1.285″ at 31″ 1.75 14.16 31
50targ33 1.700″ for 7″ then st. taper to 1.250″ at 33″ 1.75 14.88 33
50targ34 1.700″ for 7″ then st. taper to 1.250″ at 34″ 1.75 15.30 34
50targ35 1.750″ for 7″ then st. taper to 1.250″ at 35″ 1.75 16.46 35
50targ36 1.700″ for 7″ then st. taper to 1.250″ at 36″ 1.75 16.14 36
50targ37 1.700″ for 7″ then st. taper to 1.250″ at 37″ 1.75 16.56 37
50targ41 1.700″ for 7″ then st. taper to 1.250″ at 41″ 1.75 18.23 41
         
         
  Heavy target      
hvtarg31 1.750″ for 7″ then st. taper to 1.500″ at 31″ 1.75 16.66 31
hvtarg33 1.750″ for 7″ then st. taper to 1.500″ at 33″ 1.75 17.70 33
hvtarg35 1.750″ for 7″ then st. taper to 1.500″ at 35″ 1.75 18.73 35
hvtarg37 1.750″ for 7″ then st. taper to 1.500″ at 37″ 1.75 19.77 37
hvtarg38 1.750″ for 7″ then st. taper to 1.500″ at 38″ 2 20.70 38
hvtarg39 1.750″ for 7.0″ then st. taper to 1.500″ at 39″ 1.75   39
         
         
         
         
  Navy / Sporter      
50navy22 Navy or sporter contour with 1.150″ muzzle dia. at 22″ 1.75 7.64 28
50navy26 Navy or sporter contour with 1.183″ dia. muzzle at 26″ 1.75 8.95 26
50navy28 Navy contour with 1.150″ muzzle dia. at 28″ 1.75 9.34 28
50navy29 Navy contour with 1.150″ muzzle dia. at 29″ 1.75 9.62 29
50navy30 Navy contour with 1.150″ muzzle dia. at 30″ 1.75 9.92 30
50navy31 Navy contour with 1.150″ muzzle dia. at 31″ 1.75 10.18 31
50navy32 Navy contour with 1.150″ muzzle dia. at 32″ 1.75 10.47 32
50navy33 Navy contour with 1.125″ muzzle dia. at 33″ 1.75 10.57 33
50navy35 Navy contour with 1.150″ muzzle dia. at 35″ 1.75 11.32 35
50navy37 Navy contour with 1.150″ muzzle dia. at 37″ 1.75 11.88 37
navy31mo same as 50navy31 above but with muzzle of 1.265″ at 31″ 1.75 10.98 31
navy32mo same as navy31mo above but with muzzle of 1.265″ at 32″ 1.75 11.30 32
navy33mo same as navy31mo above but with muzzle of 1.265″ at 33″ 1.75 11.61 33
mcm416 1.700″ for 4.10″ then taper to 1.250″ over 1.40″ then st. taper to 1.050″ at 30″ (1.042″ at 31″) this contour is slightly smaller than the standard navy contour – was modified for 416 Barrett round 1.75 9.40 31
         
         
         
   
  Note: There is no extra charge to program for a Light Target, Heavy Target or Navy / Sporter contour at a length not specified above.
         
         
  Any other special contours will have a $50 programming charge.
  •